Who it is for and where it is used
Cannulated drills with a round shank are bone drills made to pass over a guide wire and to fit a standard drill chuck. ZHONGJIAN TECH supplies them to hospitals, surgical centres and distributors that serve operating theatres where a drill must follow a wire that is already in place and where a powered surgical drill or a hand drill with a conventional chuck is the drive in everyday use. They are used in fracture surgery to prepare pilot holes over a guide wire for cannulated screws, in hand and foot surgery where small diameters suit small bones, and in long-bone work where larger diameters prepare the way for bigger implants. They are also used in joint replacement and revision work, in spinal work where a pilot hole is needed before a screw is placed, and in veterinary orthopaedics for the same range of drilling tasks in animal bone. Because the drill is hollow along its length, the guide wire holds its line while the drill advances, which helps the surgeon keep the planned direction and position. Because the round shank is gripped directly by the chuck, theatre teams can fit the drill to any standard powered drill or hand drill without a special coupling, which makes these drills a flexible choice where several drive systems are in use. The range covers seventeen diameters from 1.5 to 6.5 mm and overall lengths from 80 to 350 mm, so one family of drills can serve a wide spread of procedures instead of many separate drill systems.
Construction and specifications
ZHONGJIAN TECH cannulated drills are precision-manufactured with a helical flute that carries bone chips away from the cutting tip as the drill advances, and with a sharp cutting point that starts on the bone surface without wandering. The hollow centre, the cannulation, runs along the length of the drill and is sized to pass over a guide wire. Cannulation is available in the range 0.8 to 5.5 mm, wider than the cannulation range of the AO quick connect version of this drill, so larger guide wires can be used; please confirm the guide-wire size required when ordering, so the matching cannulation can be supplied. Each drill is identified by its diameter and its overall length, so the right drill can be picked without ambiguity at the sterile field. Diameters are 1.5, 1.8, 2.0, 2.4, 2.5, 2.7, 3.0, 3.2, 3.8, 4.0, 4.2, 4.5, 4.8, 5.0, 5.5, 6.0 and 6.5 mm; please note that 2.4 mm appears in this range and 3.5 mm does not. Overall lengths run from 80 to 350 mm, and this product is listed by overall length only, with no separate effective length column. Maximum overall length varies by diameter: drills of 1.5 to 2.0 mm go up to 200 mm in overall length, drills of 2.5 and 2.7 mm go up to 350 mm, and drills of 3.5 mm and above start at 100 mm in overall length. The coupling is ST Round Shank, a plain round shank that is held by a standard drill chuck. Part numbers follow the pattern CST[diameter x10][overall length]; for example, CST15080 is a 1.5 mm drill, 80 mm overall, CST24140 is a 2.4 mm drill, 140 mm overall, and CST65350 is a 6.5 mm drill, 350 mm overall.
Part-number matrix — overall length (mm)
| Diameter (mm) | Cannulation (mm) | 100 mm | 350 mm |
| 2.4 | 0.8 | CST240100 | CST240350 |
| 2.5 | 0.8 | CST250100 | CST250350 |
| 2.7 | 0.8 | CST270100 | CST270350 |
| 3.0 | 1.0 | CST300100 | CST300350 |
| 3.2 | 1.0 | CST320100 | CST320350 |
| 3.8 | 1.3 | CST380100 | CST380350 |
| 4.0 | 1.3 | CST400100 | CST400350 |
| 4.2 | 1.3 | CST420100 | CST420350 |
| 4.5 | 1.5 | CST450100 | CST450350 |
| 4.8 | 1.6 | CST480100 | CST480350 |
| 5.0 | 1.6 | CST500100 | CST500350 |
| 5.5 | 1.9 | CST550100 | CST550350 |
| 6.0 | 2.0 | CST600100 | CST600350 |
| 6.5 | 2.5 | CST650100 | CST650350 |
Effective length — Cannulated Round Shank family (Effective = Overall − 25 mm)
| Overall length (mm) | Effective length (mm) |
| 100 | 75 |
| 350 | 325 |
Length limits by diameter: 2.4–2.7 mm go to 350 mm; 3.8 mm and above start at 100 mm. Only the lengths shown are tabulated for this family.
Coupling: CST — Round Shank Coupling. Other couplings in the catalog (not separate CMS products): Jacob Quick (JA), 1/4 SQ (SQ), Hudson (HU), Mini AO (MN) — Confirm before ordering. Sterile: add S to the part number.
Example: CST240100 = 2.4 mm, 0.8 mm cannulation, 100 mm overall; CST650350 = 6.5 mm, 2.5 mm cannulation, 350 mm overall.
How to order
To order, build the part number from the pattern CST[diameter x10][overall length]. First choose the diameter that matches the screw or implant that will follow the drill: 1.5 and 1.8 mm for the smallest pilot holes, 2.0 to 3.2 mm for general hand, foot and small-bone work, and 3.8 to 6.5 mm for larger screws and long-bone work, remembering that this range includes 2.4 mm and does not include 3.5 mm. Then choose the overall length that reaches the drilling depth with enough drill outside the bone for handling. Then confirm the cannulation: the range is 0.8 to 5.5 mm, so please state the guide-wire size required when ordering. Then confirm the coupling: ST Round Shank is the coupling for this product and suits a standard drill chuck. Quote the complete part number, for example CST15080, CST24140 or CST65350, when placing an order with ZHONGJIAN TECH, and state the quantity required. Drills are supplied in the diameters and overall lengths listed above, so please order from the published range and check the part number against the diameter and length tables before confirming.